Tried and True: Leftover Linen on the Band Loom

Remember that time you miscalculated when planning your warp? You found the mistake when you were threading, and you ended up with an extra group of ends. If you have ever done something like that, then you understand where this leftover linen warp came from.

New warp on the Glimakra band loom.

This little linen leftover warp is now on the Glimåkra band loom. I removed two ends to get a warp with symmetrical colors. It’s perfect for making hanging tabs to go on the leftover linen waffle weave washcloths. The weft on these band loom shuttles is from one of the little linen warp chains I mentioned last week. (See Put the Linen Back to Use.)

Leftover linen to use as weft on the band loom.
Linen from a leftover warp chain fills the little band loom shuttles.
Band Loom weaving.
Weft tails show the color variance–turquoise and blue–in the leftover linen used for weft, indistinguishable in the selvedges of the woven band.

When the thread comes to an end on the shuttle, I follow this simple process to begin a new weft.

  • Place the ending weft through the shed, leaving a tail of at least 1/2”.
How to change the weft on the band loom.
  • Without changing sheds, lightly tap the weft in place with the band knife.
  • Bring the new weft on a shuttle through the same shed, going in the same direction as the previous weft’s shuttle, leaving a tail of at least 1/2”. (There is now a weft tail extending in both directions.)
How to overlap wefts on the band loom.
How to add a new weft. Glimakra Band Loom.
  • Without changing sheds, lightly tap the new weft into place with the band knife. (This helps to make a snug fit for the two wefts in this shed.)
  • Change sheds. Beat firmly with the band knife.
  • Send the weft back through.
How to end one weft and begin another on the band loom.
  • Beat firmly, and continue weaving.
Instructions for ending and starting wefts on the band loom.
  • After weaving 1/2” further, clip off the weft tails; or, clip all the tails after the entire band is woven and has been cut from the band loom.
Linen band weaving for hanging tabs on linen washcloths.
Weft tails are left extended on this band. I may trim some of them later to 1/4″ for effect, to be used as hanging tabs on the leftover linen waffle weave washcloths.

May you put your leftovers to good use.

Happy Weaving,
Karen

6 thoughts on “Tried and True: Leftover Linen on the Band Loom

  1. Your ribbon bands add such a nice touch. Asking because I have no knowledge, how does a Band loom differ from an Inkle loom in what can be made with them?

    1. Hi Beth, There’s no difference between the band loom and an inkle loom in what can be made on them, except maybe the width. I can weave up to about 4” wide on the band loom, though I normally use it for narrow bands. I also can put on a much longer warp on the band loom than on the inkle loom. This warp on the band loom right now is probably about 5 or 6 meters long.

      The band loom is not as portable as an inkle loom, but the main advantage for me is how much faster I can weave bands on it. I can weave a band about four times faster on the band loom than on my inkle loom. The reason for this is that it has two treadles to open the sheds, making both hands free to do the continuous weaving.

      I guess the other reason I use the band loom whenever I can is it’s just plain fun!

      Thanks for asking!
      Karen

  2. Morning Karen…..I, too, have a question. Please. Do you sit and weave on the side of the loom, beating sideways….or at the end as with a regular tinkle…
    Thanks so much..I always enjoy your blog..

  3. The extra beating of the filler overlap blends the change so it is indistinguishable from the rest of the band. Who’d a thunk?
    Thank you for the lesson.
    Nannette

    1. Hi Nannette, It is surprising what a big difference this little action makes. You really cannot see where the weft changes after I clip off the weft tails.

      All the best,
      Karen

Leave a Reply to Nannette Cancel reply

Your email address will not be published. Required fields are marked *